Power supply unit - TRIO-PS-2G/1AC/24DC/10 - 2903149
- Manufactured by:
- PHOENIX CONTACT
- Price (VAT excluded)
- € 210.85
- Nuova Elva code
- 2903149
- Manufacturer code
- 2903149
- Availability
- 6 in stock
Primary-switched TRIO POWER power supply with push-in connection for DIN rail mounting, input: single phase, output: 24 V DC/10 A
Features
Save time and costs, thanks to the Push-in connection and narrow design
Increase system availability, thanks to dynamic boost with 150% of the nominal current for five seconds
Maximum flexibility due to the wide temperature range from -25°C to +70°C and device startup at -40°C
Rugged design
cULus Listed
cULus Recognized
EAC
DNV GL
IECEE CB Scheme
UL Listed
cUL Listed
UL Recognized
cUL Recognized
Specifications
| Depth | 160 mm |
|---|---|
| Height | 130 mm |
| Output Voltage | 24 V |
| Strip Length | 10 mm |
| Voltage | 10 V |
| Width | 42 mm |
Environmental Product Compliance | |
| REACh SVHC | Lead 7439-92-1 |
| China RoHS | Environmentally Friendly Use Period = 25; |
| China RoHS | For details about hazardous substances go to tab 'Downloads', Category 'Manufacturer's declaration' |
Standards | |
| EMC requirements for noise immunity | EN 61000-6-1 |
| EMC requirements for noise immunity | EN 61000-6-2 |
| EMC requirements for noise emission | EN 61000-6-3 |
| EMC requirements for noise emission | EN 61000-6-4 |
| Standard - Safety of transformers | EN 61558-2-16 (air clearances and creepage distances only) |
| Standard - Electrical safety | IEC 60950-1/VDE 0805 (SELV) |
| Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations | EN 50178/VDE 0160 (PELV) |
| Standard – Safety extra-low voltage | IEC 60950-1 (SELV) and EN 60204-1 (PELV) |
| Standard - Safe isolation | DIN VDE 0100-410 |
| Standard – Limitation of mains harmonic currents | EN 61000-3-2 |
| Rail applications | EN 50121-4 |
Dimensions | |
| Width | 42 mm |
| Height | 130 mm |
| Depth | 160 mm |
| Installation distance right/left | 0 mm / 0 mm |
| Installation distance top/bottom | 50 mm / 50 mm |
Output data | |
| Nominal output voltage | 24 V DC ±1 % |
| Setting range of the output voltage (USet) | 24 V DC - 28 V DC (constant capacity) |
| Nominal output current (IN) | 10 A |
| Dynamic Boost (IDyn.Boost) | 15 A (5 s) |
| Derating | > 60 °C - 70 °C (2.5%/K) |
| Connection in parallel | Yes, for redundancy and increased capacity |
| Connection in series | yes |
| Feedback voltage resistance | ≤ 35 V DC |
| Protection against overvoltage at the output (OVP) | ≤ 30 V DC |
| Control deviation | < 1 % (change in load, static 10 % - 90 %) |
| Control deviation | < 3 % (Dynamic load change 10 % - 90 %, 10 Hz) |
| Control deviation | < 0.1 % (change in input voltage ±10 %) |
| Residual ripple | < 10 mVPP (with nominal values) |
| Output power | 240 W |
| Typical response time | < 1 s |
| Maximum power dissipation in no-load condition | < 5.1 W (230 V) |
| Power loss nominal load max. | < 25 W |
EMC data | |
| Electromagnetic compatibility | Conformance with EMC Directive 2014/30/EU |
| Low Voltage Directive | Conformance with Low Voltage Directive 2014/35/EC |
| Electrostatic discharge | EN 61000-4-2 |
| Contact discharge | 6 kV (Test Level 4) |
| Discharge in air | 8 kV (Test Level 4) |
| Electromagnetic HF field | EN 61000-4-3 |
| Frequency range | 80 MHz - 1 GHz |
| Frequency range | 1 GHz - 2 GHz |
| Test field strength | 10 V/m (Test Level 3) |
| Frequency range | 2 GHz - 3 GHz |
| Comments | Criterion A |
| Fast transients (burst) | EN 61000-4-4 |
| Input | 4 kV (Test Level 4 - asymmetrical) |
| Output | 2 kV (Test Level 3 - asymmetrical) |
| Signal | 1 kV (Test Level 2 - asymmetrical) |
| Surge voltage load (surge) | EN 61000-4-5 |
| Input | 3 kV (Test Level 3 - symmetrical) |
| Input | 6 kV (Test Level 4 - asymmetrical) |
| Output | 1 kV (Test Level 2 - symmetrical) |
| Output | 2 kV (Test Level 1 - asymmetrical) |
| Comments | Criterion B |
| Conducted interference | EN 61000-4-6 |
| Frequency range | 0.15 MHz - 80 MHz |
| Voltage | 10 V (Test Level 3) |
| Criterion A | Normal operating behavior within the specified limits. |
| Criterion B | Temporary impairment to operational behavior that is corrected by the device itself. |
Input data | |
| Nominal input voltage range | 100 V AC - 240 V AC |
| Nominal input voltage range | 110 V DC - 250 V DC |
| Input voltage range | 100 V AC - 240 V AC -15 % - +10 % |
| Input voltage range | 110 V DC - 250 V DC -10 % - +10 % |
| Dielectric strength maximum | 300 V AC 15 s |
| AC frequency range | 50 Hz - 60 Hz ±10 % |
| Discharge current to PE | < 3.5 mA |
| Current consumption | 3.1 A (100 V AC) |
| Current consumption | 2.4 A (120 V AC) |
| Current consumption | 1.3 A (230 V AC) |
| Current consumption | 1.4 A (240 V AC) |
| Nominal power consumption | 285 VA |
| Inrush current | ≤ 25 A (typical) |
| Mains buffering time | typ. 15 ms (120 V AC) |
| Mains buffering time | typ. 20 ms (230 V AC) |
| Input fuse | 6.3 A (internal (device protection)) |
| Recommended breaker for input protection | 6 A - 16 A (Characteristics B, C, D, K) |
| Power factor (cos phi) | 0.93 |
| Type of protection | Transient surge protection |
| Protective circuit/component | Varistor |
Ambient conditions | |
| Ambient temperature (storage/transport) | -40 °C - 85 °C |
| Max. permissible relative humidity (operation) | ≤ 95 % (at 25 °C, non-condensing) |
| Climatic class | 3K3 (in acc. with EN 60721) |
| Degree of pollution | 2 |
| Installation height | ≤ 5000 m (> 2000 m, Derating: 10 %/1000 m) |
| Degree of protection | IP20 |
| Inflammability class in acc. with UL 94 (housing / terminal blocks) | V0 |
| Ambient temperature (operation) | -25 °C - 70 °C (> 60 °C Derating: 2.5 %/K) |
| Ambient temperature (start-up type tested) | -40 °C |
Connection data, input | |
| Connection method | Push-in connection |
| Conductor cross section solid min. | 0.2 mm² |
| Conductor cross section solid max. | 4 mm² |
| Conductor cross section flexible min. | 0.2 mm² |
| Conductor cross section flexible max. | 2.5 mm² |
| Conductor cross section AWG min. | 24 |
| Conductor cross section AWG max. | 12 |
| Stripping length | 10 mm |
Connection data, output | |
| Connection method | Push-in connection |
| Conductor cross section solid min. | 0.2 mm² |
| Conductor cross section solid max. | 4 mm² |
| Conductor cross section flexible min. | 0.2 mm² |
| Conductor cross section flexible max. | 2.5 mm² |
| Conductor cross section AWG min. | 24 |
| Conductor cross section AWG max. | 12 |
| Stripping length | 8 mm |
Conformance/approvals | |
| UL approvals | UL Listed UL 508 |
| UL approvals | UL/C-UL Recognized UL 60950-1 |
Connection data for signaling | |
| Connection method | Push-in connection |
| Conductor cross section solid min. | 0.2 mm² |
| Conductor cross section solid max. | 1.5 mm² |
| Conductor cross section flexible min. | 0.2 mm² |
| Conductor cross section flexible max. | 1.5 mm² |
| Conductor cross section AWG min. | 24 |
| Conductor cross section AWG max. | 16 |
| Stripping length | 8 mm |
